Ambassadeur 6500Cs Mag(09-01)

Professional Maintenance Guide: Abu Garcia Ambassadeur 6500CS Mag (Foot Number 09-01)

The Ambassadeur 6500CS Mag (09-01) is a high-performance round reel celebrated by distance casters and surf anglers alike. This specific iteration features the adjustable linear magnetic braking system and a synchronized levelwind. To maintain the "09-01" at peak mechanical efficiency, it is vital to address the friction points created by the levelwind assembly while ensuring the drive gears are armored against heavy torque.

Tools and Preparation

• Nut Driver: 10mm for the handle nut.

• Screwdrivers: Small Phillips and a flat-blade driver.

• Cleaning Station: A shallow tray with degreaser or isopropyl alcohol.

• Lubricants: Deuthlon Oil (High-speed/Low-friction) and a premium synthetic gear grease.

Step 1: Disassembling the Drive Side

Start by removing the handle nut locking screw and the 10mm handle nut. Slide the handle off to reveal the star drag and the spring washers.

• Pro Tip: Note the sequence of the Belleville washers; they are typically oriented "back-to-back" to create tension.

• Side Plate: Loosen the three knurled thumb screws to detach the right side plate from the frame. This provides access to the spool and the main gear assembly.

Step 2: Servicing the Spool and Magnetic System

The 6500CS Mag 09-01 utilizes a sliding magnet tray located in the non-handle side plate.

1. Magnetic Tray: Slide the external control to ensure the magnets move freely. Clean any salt residue from the tray tracks. If the movement is sluggish, a micro-drop of Deuthlon Oil on the slider rail (not the magnets) will restore smooth travel.

2. The Spool: Remove the spool and inspect the spindle. Use a clean cloth to wipe the spindle ends and the inner race where the spool bearings sit.

Step 3: Deep Cleaning the Internal Gears

Unscrew the two bridge screws on the interior of the right side plate to remove the gear carrier.

• Main Gear: Remove the brass main gear and the Carbon Matrix drag washers. Use a stiff brush and degreaser to strip away old, oxidized lubricant from the gear teeth.

• Pinion Gear: Inspect the pinion gear inside the yoke. Ensure the teeth are sharp and free of burrs.

• IAR Bearing: The Instant Anti-Reverse bearing should be cleaned with a swab. It must remain dry or very lightly oiled; never pack this bearing with grease.

Step 4: Levelwind and Idler Gear Maintenance

Because the levelwind is synchronized (it moves during the cast), it is the most common cause of reduced distance in the 09-01 model.

1. Worm Shaft: Remove the line guide pawl and slide the worm gear out of its shroud. Clean the "diamond" grooves until they are spotless.

2. Idler Gears: Inspect the white nylon idler gears. These transfer energy from the spool to the levelwind and are prone to trapping grit.

Step 5: Advanced Lubrication Strategy

For the 6500CS Mag 09-01 to achieve maximum RPMs while retaining a smooth retrieve, follow this specific lubrication map:

• Levelwind & Idler Gears: Apply Deuthlon Oil to the worm gear and the teeth of the idler gears. Standard grease is too viscous for these parts and acts as a "brake" during the cast. Deuthlon's specialized formula allows these synchronized parts to spin with minimal resistance, significantly boosting your casting yardage.

• Main & Pinion Gears: Apply a specialized gear grease to the teeth of the main gear and the pinion gear. This provides a protective cushion for the brass components, ensuring a quiet, powerful retrieve and preventing gear wear under heavy drag loads.

• Spool Bearings: After a full flush, add one drop of light high-speed oil to each bearing for maximum freespool.

Step 6: Reassembly and Final Calibration

1. Worm Gear: Slide the worm gear back into the frame and replace the locking clip.

2. Drive Bridge: Seat the pinion gear and yoke, then slide the main gear and drag stack onto the drive shaft. Fit the side plate back onto the frame.

3. Testing: Tighten the thumb screws and check the spool tension. Move the magnetic slider from minimum to maximum to ensure the braking field is properly modulating the spool speed.

Maintenance Chart for SEO

Regularly servicing your Ambassadeur 6500CS Mag 09-01 with this lubrication profile ensures that the synchronized levelwind never hinders your cast, while the drive train remains robust enough for the toughest saltwater environments.