Ambassadeur 5600 Pro Max (03-00)

Professional Maintenance Guide: Abu Garcia Ambassadeur 5600 Pro Max (03-00)

The Ambassadeur 5600 Pro Max (03-00) represents a high-performance peak in the round reel lineage, featuring an advanced one-piece frame and a multi-bearing system designed for tournament-level precision. This model is engineered for maximum sensitivity and casting speed. To maintain the "Pro Max" designation of this 03-00 iteration, a meticulous teardown and the application of high-end synthetic lubricants are required to protect its precision-machined internal components.

Phase 1: Disassembly and Internal Inspection

Proper service of the Pro Max requires a systematic approach to ensure the high-speed drive train and specialized bearings are correctly maintained.

1. Frame Separation: Loosen the three captive thumb screws on the handle-side plate. Carefully pull the plate assembly away from the frame.

2. Spool Service: Slide the spool out of the frame. Inspect the spool shaft and the high-performance bearings. In the Pro Max series, these bearings are often shielded or feature specific tolerances; ensure they are free of any micro-debris.

3. Drive Train Access: Remove the handle nut, handle, and star drag. Take care not to lose the spring washers and the small clicker components under the drag star. Lift the side plate cover to expose the main gear and the pinion yoke.

4. Cleaning Protocol: Submerge the brass main gear, stainless steel pinion gear, and the worm shaft in a high-quality solvent. Use a soft brush to ensure the gear valleys are spotless. Dry all components completely before re-lubricating.

Phase 2: Precision Lubrication with Deuthlon

To keep the 5600 Pro Max running with elite smoothness, we recommend using Deuthlon Reel Grease and Deuthlon Reel Oil. These specialized products provide a superior film strength that stays on the gears even under high rotational speeds.

Grease Application (Deuthlon Reel Grease):

• Main Drive Gear: Apply a light, uniform coating of grease to the teeth of the brass main gear. This provides the necessary cushion to prevent gear "chatter" and ensures a silent, powerful retrieve under load.

• Pinion Gear: Coat the teeth of the pinion gear and the internal slot where it interfaces with the spool shaft. Proper lubrication here is essential for preventing wear and ensuring the reel engages crisply when the handle is turned.

• Clutch & Slide Plates: Apply a micro-layer of grease to the sliding metal surfaces of the clutch to ensure the thumb bar operates with a crisp, tactile click.

Oil Application (Deuthlon Reel Oil):

• Levelwind Worm Gear: Apply two drops of oil to the spiral worm gear. Since the levelwind is constantly oscillating during both the cast and retrieve, oil offers the low-viscosity protection needed to prevent drag and wear on the pawl.

• Idler Gears: These gears link the spool's rotation to the line-lay system. A light coating of oil ensures they spin with minimal resistance, which is vital for maintaining the casting efficiency of the Pro Max series.

• Spool Bearings: Flush the bearings thoroughly and apply one drop of Deuthlon oil to each. This ultra-thin lubrication allows the spool to reach high RPMs without the "fluid drag" associated with heavier lubricants.

Phase 3: Reassembly and Operational Testing

1. Seat the Spool: Slide the spool back into the frame, ensuring the shaft is properly aligned with the non-handle side bearing.

2. Housing Alignment: Position the side plate over the frame, ensuring the pinion gear seats over the spool shaft correctly. Hand-tighten the thumb screws in a cross-pattern to ensure even pressure.

3. Check the Oscillation: Rotate the handle to verify that the levelwind tracks smoothly and evenly across the front of the reel.

4. Final Spin Test: Disengage the thumb bar. The spool should spin silently and freely. Adjust the mechanical tension knob to eliminate spool side-play, allowing the Pro Max system to handle the rotational load with peak efficiency.

Maintenance Reference Table